**Invisible Charger Solution Review**

As I sit at my desk, I can see that this is the back side of the drawer that I have on my desk and this is about the amount of size or room that I have between the back of my desk and the edge of the desk. What I'm planning to do is use this mounting bracket right about here to be able to mount the invisible charger. So, what we're going to do is go ahead and take off the adhesive pads here.

Now, I'm going to position it exactly a half inch back from the edge so for mine, what I'm going to do is I'm going to go ahead and slide this cable through here. That way, it's got a little bit of resistance and won't slide out and fall there. Now that fits in there very nicely, snug. You can see that the connector is here.

Each one of these is kind of taped down to the bottom of the table. This is nice and secure. I can take this part of the cable here plug it in to the QC 3.0 charger, and then we will go back up to the top of the desk and see if we can position things correctly.

Alrighty now that we've got it installed on the bottom of the desk, I move my camera over a little bit, and you can see that it's basically installed at this part of the desk. I was over here installing it earlier, and if I reach under, I can feel it right about here in theory. I should be able to take my phone set it here, and it charges right. That's pretty awesome.

I mean, right off the bat, I'm almost done. Right but what they do is give you this nice little alignment card that we talked about earlier. Okay, all right. So now we've moved it right to about the perfect spot, and what I can do is I can take this black sticker right here or this white sticker right here, and I can put it down exactly where this is, and that's just going to probably amplify the signal a little bit.

But I think I want to go ahead and use it without the sticker for now because I like the look of the clean desk. I mean, I just want to see how it works right. But if I wanted to, I would just remove this, and put that sticker there.

What I can see is that generally along this dark part of the line of my desk and just a little bit left of this seam is where I want to put the phone if I want to charge it. So, if I set it here, I'm charging, and I'm good to go. If I take it off, put it here, it's charging.

So now, I've basically got a nice open spot on my desk that anytime I'm working, I can just set my phone up here not even think about it, and it's charging. To put this on there, then I do have a sort of signal booster which you know let me down, let me know down in the comments whether or not you would use this or you would just use it without it.

But either way, it seems to work good. So at this point in time, I think we have a thumbs up winner here. I mean a super easy to use, super duper easy to install charging block that fits underneath a pretty thick desk like this. I mean, this sucker's you know about this thick um it allows me to basically just stick my phone there any point in time that I want, and it charges really consistently.

I'm going to be thrilled with this, and I'll be using it all the time. So again, thanks to the folks at Capon for sending this over. I will put the link down below so that you'll be able to check this out and see if it's something you might want to get for yourself.

I think I'm going to go grab another one for my stepdad; he's got a desk similar to this, and he would enjoy that a lot. But again, comment down below if you're thinking about getting one of these uh I think it's awesome. Um, please hit the thumbs up subscribe if you like this, and for now, this is Carl from Technical Goodies, and I'm out.

WEBVTTKind: captionsLanguage: enwhat's up everybody this is Carl from technical goodies and today we are taking a look at something I think is actually pretty cool so previously you might have seen that I have this little wireless charger provided by kpon that is a thick case wireless charger now I've really enjoyed this I've really enjoyed using this um what it allows you to do is have it on your desk and charge phones that have like OtterBoxes on it and stuff like that so what they did was they also sent through this invisible wireless charger now what's special about this one is that it mounts to the underneath of your desk and basically allows you to take and set your phone on your desk while the Charger's underneath and charge without any visible sign of there being a charger so I figured since they sent it through let's go ahead and connect it to my table here and try it out see how it works now one thing to note about this particular charger it does have a Max charging distance of 30 millimeters which is about 1.18 inches my desk here happens to be be it's kind of like a workbench it's a husky workbench it does fit within that uh Max charging distance so it should be able to work so let's go ahead and just take a look what's inside the box here we'll get it all out see what we got see what sort of installation it takes and get it working so as you can see in the Box you have the primary charging disk in relation it's a little bit bigger than the one that they sent previously for the thick wireless charger this is what mounts underneath and this is a little mounting bracket and as you can see kind of got a little slot and I believe what happens is this kind of slots into here and stays there underneath the desk and these are some adhesive tabs looks like you can also screw them in if you want so that's a good option if you're having any issue with adhesive underneath your desk if so we've got the charging pad itself the mounting bracket um this what I'm understanding is this is a amplifier disc okay so if you have a desk that is closer to the 30 millimeter Mark you may need to do use this on top of your desk or if you want an idea of a positioning place of where you want to be able to put your phone down then you would be able to stick this down on your desk and you'd have a nice little spot where you'd know exactly where your phone is going to charge I'm going to try it without this first but we can try it with and without and see how it works so the other good thing that it looks like they put in here is a alignment assistant okay so this I think allows us to be able to mount this to the bottom of the desk and then take this and figure out exactly where the best position is for the alignment and that way you can take this and kind of put it exactly where the best most optimal spot is for charging with this obviously in here oh that's nice so they give you both the the black one and the white stickers um they do they do give you a quick charging 3.0 charging block and I believe you must use the 3.0 block with this yeah it says here it says you have to use the q3c adapter to be able to use this and that gives it enough power to be able to push through the desk I definitely say what you don't want to do is you don't want to charge your phone directly on top of here because there's too much magnetic charging strength coming through and it could potentially damage your phone if you're going directly on top of this plate because it's designed to go through larger surfaces like this desk and it looks like they provide a nice USBC to USB a cable now one of the difficulties I'm going to have with this particular desk is that I've got a large drawer on the bottom of this desk and my question in my head is am I going to try to you know put the put the charger here or am I going to put it over here or where exactly on my desk I'm actually thinking of maybe having it kind of over here out of the way so that way I'm doing the typically the most of my work I'll be able to have something charging here kind of out of the way but still accessible and then it won't conflict with the drawer that's underneath so at this point in time I think all we have to do is install it and see if it works let's give it a try Okay so as you can see I've got the camera here pointed up at the back of my desk um you can see that this is the back side of the drawer that I have on my desk and this is about the amount of size or room that I have between the back of my desk and the edge of the desk so what I'm planning to do is use this mounting bracket right about here to be able to mount the invisible charger so the what we're going to do is go ahead and take off the take off the adhesive pads here now I'm going to position it exactly about a half inch back from the edge so for mine what I'm going to do is I'm going to go ahead and slide this cable through here that way it's got a little bit of once it's in it's got a little bit of resistance and won't slide out and fall there now that fits in there very nicely snug you can see that the connector is here that's hidden each one of these are kind of taped down to the bottom of the table this is nice and secure I can take this part of the cable here plug it in to the QC 3.0 charger and then we will go back up to the top of the desk and see if we can position things correctly alrighty now that we've got it installed on the bottom of the desk I move my camera over a little bit and you can see that it's basically installed at this part of the desk I was over here installing it earlier and if I reach under I can feel it right about here in theory I should be able to take my phone set it here and it charges right that's pretty awesome I mean right off the bat I'm almost done right but what they do is they give you this nice little alignment card that we talked about earlier okay all right so now we've moved it right to about the perfect spot and what I can do is I can do one of two things right so I can take this black sticker right here or this white sticker right here and I can put it down exactly where this is and that's just going to probably amplify the signal a little bit but I think I want to go ahead and use it without the sticker for now because I like the look of the clean desk I mean I just want to see how it works right so but if I wanted to I would just remove this and put that sticker there but what I can see is that generally along this dark part of the line of my desk and just a little bit left of this seam is where I want to put the phone if I want to charge it so if I set it here I'm charging and I'm good to go if I take it off put it here it's charging so now I've basically got a nice open spot on my desk that anytime I'm working I can just set my phone up here not even think about it and it's charging this is just sitting there ready to go foreign to put that on there then I do have a sort of signal booster which you know I don't know let me down let me know down in the comments whether or not you would use this or you would just use it without it but either way it seems to work good so at this point in time I think we have a thumbs up winner here I mean a super easy to use super duper easy to install charging block that fits underneath a pretty thick desk like this I mean this sucker's you know about this thick um it allows me to basically just stick my phone there any point in time that I want and it charges really consistently I'm going to be thrilled with this and I'll be using it all the time so again thanks to the folks at Capon for sending this over I will put the link down below so that you'll be able to check this out and see if it's something you might want to get for yourself I think I'm going to go grab another one for my stepdad he's got a desk similar to this and he would enjoy that a lot but again comment down below if you're thinking about getting one of these uh I think it's awesome um please hit the thumbs up subscribe if you like this and for now this is Carl from technical goodies and I'm outwhat's up everybody this is Carl from technical goodies and today we are taking a look at something I think is actually pretty cool so previously you might have seen that I have this little wireless charger provided by kpon that is a thick case wireless charger now I've really enjoyed this I've really enjoyed using this um what it allows you to do is have it on your desk and charge phones that have like OtterBoxes on it and stuff like that so what they did was they also sent through this invisible wireless charger now what's special about this one is that it mounts to the underneath of your desk and basically allows you to take and set your phone on your desk while the Charger's underneath and charge without any visible sign of there being a charger so I figured since they sent it through let's go ahead and connect it to my table here and try it out see how it works now one thing to note about this particular charger it does have a Max charging distance of 30 millimeters which is about 1.18 inches my desk here happens to be be it's kind of like a workbench it's a husky workbench it does fit within that uh Max charging distance so it should be able to work so let's go ahead and just take a look what's inside the box here we'll get it all out see what we got see what sort of installation it takes and get it working so as you can see in the Box you have the primary charging disk in relation it's a little bit bigger than the one that they sent previously for the thick wireless charger this is what mounts underneath and this is a little mounting bracket and as you can see kind of got a little slot and I believe what happens is this kind of slots into here and stays there underneath the desk and these are some adhesive tabs looks like you can also screw them in if you want so that's a good option if you're having any issue with adhesive underneath your desk if so we've got the charging pad itself the mounting bracket um this what I'm understanding is this is a amplifier disc okay so if you have a desk that is closer to the 30 millimeter Mark you may need to do use this on top of your desk or if you want an idea of a positioning place of where you want to be able to put your phone down then you would be able to stick this down on your desk and you'd have a nice little spot where you'd know exactly where your phone is going to charge I'm going to try it without this first but we can try it with and without and see how it works so the other good thing that it looks like they put in here is a alignment assistant okay so this I think allows us to be able to mount this to the bottom of the desk and then take this and figure out exactly where the best position is for the alignment and that way you can take this and kind of put it exactly where the best most optimal spot is for charging with this obviously in here oh that's nice so they give you both the the black one and the white stickers um they do they do give you a quick charging 3.0 charging block and I believe you must use the 3.0 block with this yeah it says here it says you have to use the q3c adapter to be able to use this and that gives it enough power to be able to push through the desk I definitely say what you don't want to do is you don't want to charge your phone directly on top of here because there's too much magnetic charging strength coming through and it could potentially damage your phone if you're going directly on top of this plate because it's designed to go through larger surfaces like this desk and it looks like they provide a nice USBC to USB a cable now one of the difficulties I'm going to have with this particular desk is that I've got a large drawer on the bottom of this desk and my question in my head is am I going to try to you know put the put the charger here or am I going to put it over here or where exactly on my desk I'm actually thinking of maybe having it kind of over here out of the way so that way I'm doing the typically the most of my work I'll be able to have something charging here kind of out of the way but still accessible and then it won't conflict with the drawer that's underneath so at this point in time I think all we have to do is install it and see if it works let's give it a try Okay so as you can see I've got the camera here pointed up at the back of my desk um you can see that this is the back side of the drawer that I have on my desk and this is about the amount of size or room that I have between the back of my desk and the edge of the desk so what I'm planning to do is use this mounting bracket right about here to be able to mount the invisible charger so the what we're going to do is go ahead and take off the take off the adhesive pads here now I'm going to position it exactly about a half inch back from the edge so for mine what I'm going to do is I'm going to go ahead and slide this cable through here that way it's got a little bit of once it's in it's got a little bit of resistance and won't slide out and fall there now that fits in there very nicely snug you can see that the connector is here that's hidden each one of these are kind of taped down to the bottom of the table this is nice and secure I can take this part of the cable here plug it in to the QC 3.0 charger and then we will go back up to the top of the desk and see if we can position things correctly alrighty now that we've got it installed on the bottom of the desk I move my camera over a little bit and you can see that it's basically installed at this part of the desk I was over here installing it earlier and if I reach under I can feel it right about here in theory I should be able to take my phone set it here and it charges right that's pretty awesome I mean right off the bat I'm almost done right but what they do is they give you this nice little alignment card that we talked about earlier okay all right so now we've moved it right to about the perfect spot and what I can do is I can do one of two things right so I can take this black sticker right here or this white sticker right here and I can put it down exactly where this is and that's just going to probably amplify the signal a little bit but I think I want to go ahead and use it without the sticker for now because I like the look of the clean desk I mean I just want to see how it works right so but if I wanted to I would just remove this and put that sticker there but what I can see is that generally along this dark part of the line of my desk and just a little bit left of this seam is where I want to put the phone if I want to charge it so if I set it here I'm charging and I'm good to go if I take it off put it here it's charging so now I've basically got a nice open spot on my desk that anytime I'm working I can just set my phone up here not even think about it and it's charging this is just sitting there ready to go foreign to put that on there then I do have a sort of signal booster which you know I don't know let me down let me know down in the comments whether or not you would use this or you would just use it without it but either way it seems to work good so at this point in time I think we have a thumbs up winner here I mean a super easy to use super duper easy to install charging block that fits underneath a pretty thick desk like this I mean this sucker's you know about this thick um it allows me to basically just stick my phone there any point in time that I want and it charges really consistently I'm going to be thrilled with this and I'll be using it all the time so again thanks to the folks at Capon for sending this over I will put the link down below so that you'll be able to check this out and see if it's something you might want to get for yourself I think I'm going to go grab another one for my stepdad he's got a desk similar to this and he would enjoy that a lot but again comment down below if you're thinking about getting one of these uh I think it's awesome um please hit the thumbs up subscribe if you like this and for now this is Carl from technical goodies and I'm out