Putting a Screen Protector on Your iPad 4 with Armor Suit

Before you begin, make sure your table is clean and so are your fingertips and hands. As you can see from the contents of the package, we have a little towel for your fingers and screen to remove any smudges and dust, a card that's quite flexible for using as a squeegee to get rid of extra air bubbles, a solution for your fingertips and screen, and the screen protector itself. The first thing you want to do is ensure that your device is shut down.

Next, use the little towel to try to remove all the smudges and fingerprints from the screen. Be sure to press lightly so as not to damage your screen. After that, take the solution and spray it onto your fingertips, making sure your hands are completely moist so you don't leave any finger marks or smudges on the screen. Now, take the protector and spray the solution on the non-adhesive side, trying to do so evenly as possible. Once done, begin peeling the screen protector from its backing.

Make sure the entire adhesive side of the protector is sprayed before placing it on your iPad. Ensure all the dust has been removed from the screen, which may require using this protector again if necessary. Slowly place the screen onto the iPad and line everything up first by aligning the home screen button and camera hole, then hold the screen in place as you begin to squeegee out any remaining water and air bubbles. After getting rid of these, your screen should look something like this.

Finally, remove the home button from its backing, spray it once more, and apply it to the iPad. To get rid of excess solution, use the cloth provided to soak up fingerprints or smudges. Use the cloth one final time to remove any remaining fingerprints. Please make sure you're not wearing nail polish because the adhesive can easily remove it, which could lead to trouble under your screen later on. Lastly, keep your iPad closed for 24 hours as this is recommended.

After following these steps, hopefully, your new Armor Suit protector will help protect your screen from damage and provide a clear view when using your device.

"WEBVTTKind: captionsLanguage: entoday we're going to be putting a screen protector on iPad 4 the particular screen protector that we're using is armor suit the first thing you want to do is make sure that your table is clean and also your fingertips and hands are clean as you can see the different contents that comes in the package is a little towel for your fingers and for the screen that will remove any of the smudges and dust a card which is quite flexible for you to use use to squeegee out any of the extra air bubbles a solution for your fingertips and the screen and the screen itself the first thing you want to do is make sure that your device is shut down next thing you want to do is use the little towel to try to remove all of the smudges and fingerprints you want to make sure that you're pressing lightly so that you do not damage your screen the next thing you want to do is take the solution and spray your fingertips make sure that your hands are completely moist so that you don't leave any of your finger marks or smudges on the screen next you want to take the protector and spray the solution on the non-adhesive as side try to spray it as evenly as possible after doing so you can begin to peel the screen protector from the backing after peeling the screen protector from the backing make sure that the entire adhesive side of the protector is sprayed before placing the screen protector on the iPad you want to make sure that your all the dust has been removed from the screen so you may have to use this once again then slowly place the screen onto the iPad and line everything up first you want to align the home screen button and then the camera hole and then you hold the screen so it doesn't move and begin to squeegy it out as you can see it's beginning to move after you squeegee out the rest of the water and air bubbles this is what it should look like finally remove the home button from the backing spray it once and then put it on to the after doing so you're going to want to soak up any excess solution using the cloth that was given to remove any of the fingerprints or smudges and then use the cloth one final time to remove fingerprints now you want to make sure that you aren't wearing any nail polish because the adhesive can remove it very easily and it'll get stuck under your screen and it's difficult to remove also you want to make sure that you keep your iPad closed for 24 hours you may also see that there is a gray tint underneath and there's a few marks and once the solution dries those should go away and this is how you put on the armor suit protector and hopefully it helps youtoday we're going to be putting a screen protector on iPad 4 the particular screen protector that we're using is armor suit the first thing you want to do is make sure that your table is clean and also your fingertips and hands are clean as you can see the different contents that comes in the package is a little towel for your fingers and for the screen that will remove any of the smudges and dust a card which is quite flexible for you to use use to squeegee out any of the extra air bubbles a solution for your fingertips and the screen and the screen itself the first thing you want to do is make sure that your device is shut down next thing you want to do is use the little towel to try to remove all of the smudges and fingerprints you want to make sure that you're pressing lightly so that you do not damage your screen the next thing you want to do is take the solution and spray your fingertips make sure that your hands are completely moist so that you don't leave any of your finger marks or smudges on the screen next you want to take the protector and spray the solution on the non-adhesive as side try to spray it as evenly as possible after doing so you can begin to peel the screen protector from the backing after peeling the screen protector from the backing make sure that the entire adhesive side of the protector is sprayed before placing the screen protector on the iPad you want to make sure that your all the dust has been removed from the screen so you may have to use this once again then slowly place the screen onto the iPad and line everything up first you want to align the home screen button and then the camera hole and then you hold the screen so it doesn't move and begin to squeegy it out as you can see it's beginning to move after you squeegee out the rest of the water and air bubbles this is what it should look like finally remove the home button from the backing spray it once and then put it on to the after doing so you're going to want to soak up any excess solution using the cloth that was given to remove any of the fingerprints or smudges and then use the cloth one final time to remove fingerprints now you want to make sure that you aren't wearing any nail polish because the adhesive can remove it very easily and it'll get stuck under your screen and it's difficult to remove also you want to make sure that you keep your iPad closed for 24 hours you may also see that there is a gray tint underneath and there's a few marks and once the solution dries those should go away and this is how you put on the armor suit protector and hopefully it helps you\n"